Название | : | How To Solder Led Strip Lights - How To Cut and Solder RGB LED Strip Lights |
Продолжительность | : | 8.46 |
Дата публикации | : | |
Просмотров | : | 408 rb |
|
Thanks helped a whole lot I appreciate people like you Comment from : Ricardo Martinez |
|
How are these not shorting?brIt seems like you get the solder covering both the green and yellow pins at 5:03 Comment from : Oxo Nomy |
|
what temp thoooo Comment from : Creepy Crawling |
|
Yea but what about the power that seems like it'd be the most important part Comment from : RetailPale |
|
Great video bro! Helped a lot! Comment from : Noahwaydude |
|
I am really distracted by the poor camera focus Comment from : Pierre Hamelin |
|
what temperature on soldering tool ? it heats through the wire instantly , something i cant get :( Comment from : Evermystic designs |
|
Thanks Great video To heat the heat sync is a butane torch too powerful? Comment from : Bill Patterson |
|
Good stuff Dude! Thanks🌟 Comment from : Johann K |
|
what temp is your iron set at? Comment from : Bill Jones |
|
So what the hell do you do when the solder refuses to stick to the copper pads? Because I cannot get the solder to stick to the copper AT ALL Comment from : Brady |
|
What temperature do you use?brI find it easier to tape the led strip to the table so it Will lie completely still and not move Comment from : Jesper Svensson |
|
Nice Comment from : Five Stars |
|
Thank you so much Comment from : paint Remedies |
|
Exciting I think not Exciting is something that happens when you skydive Comment from : Ben Reavely |
|
Just did a few myself, quick tip to make sure nothings shorted out with a multimeter on continuity before putting on the heat shrink Comment from : djlykaen |
|
My soldering iron is not sticking the melted wire🥹 Comment from : THE TRICKSTER |
|
Can you fix a chewed up wire from led underglow lights? Wasn't sure If I can snip wires put back together an put black electric tape around them an put back together? Hope I can!! Comment from : Nicholas Hanson |
|
8 minutes to solder a wire come on Comment from : Warren Capes |
|
Question; The exposed wiring on the strip and under the heat shrink won’t short out if they make contact? Comment from : MAKMusik |
|
Hi thank you for that information I am about to start wiring my Enterprise but haveing trouble finding a on of switch Comment from : Alan Royal |
|
Is it okay if there is solder already on it? Am I able to melt it away and put new solder? Comment from : Juan Lopez |
|
Work the other way around, starting with black and work upwards to yellow That way the iron goes further away the wire you just soldered Comment from : kef |
|
Dude, how does it stick to your wires so quickly?brbrI tried so many attempts to coat that wires but always end up doing it wrongbrbrDo I need higher temperature? Comment from : GembleRsK |
|
😂 I have 6 rabbit's So yeah they chewed my rgb led strip Plus other pets in the past I save so much by learning Thank you sir Comment from : skepticalgenious |
|
I sure as hell should have watched this video before i wasted 2 hours trying to wire those damn things up Awesome time and headache saving video Thank you sir Comment from : Ry Ry |
|
Need some help finding a strip for a project Could I get an email to message you for some tips Comment from : Guillermo Vazquez |
|
What happens if any of the 4 solder connections touch each other? Comment from : Falling Awake |
|
Thanks for the tutorial, Chad Comment from : Empoleon |
|
anyone notice the fly att 7:53 ? Comment from : Luka K Vlogs |
|
I’ve experimented with many different types of solder and soldering irons, and surprisingly, what works best for me is hiring an electrician Comment from : Guy Ross |
|
I'm did all the steps and ideas you said but my led just turns into ball blobs and doesn't stick to the strip copper pads neither with the soldering iron Comment from : Drrrw |
|
Wire Guy should talk to Camera Guy about how to macro focus Comment from : Snail Tale |
|
Why do you want to solder them, being 100 serious I legit don't see the point when u just plug them in? Comment from : Mandy |
|
Nice video but please reduce the BG sound Comment from : Daan Pyrography |
|
The solder is not sticking to my let's pad Any suggestions? I'm very new to this Comment from : Bartsim23 |
|
Great video, but for us who dont know was that battery a standard 12 volt like a car battery? Can a 9 volt work too? Comment from : frank Reilly |
|
Thank you,thank you soo much for explaining instead of just music and very vague if any communication Comment from : Quentin Rawlins |
|
I see you love Ikea Lack tables so does the entire 3D printing community You need to get a printing farm going and use each one as an enclosure You can pimp it out with LED galore Nice video btw Comment from : Osiris Rex |
|
Thanks for the video! I don’t solder much so it will help a lot One thing I noticed in your video is the order of soldering when you did the second connection you had to go over the first one and inadvertently unsoldered the first Wouldn’t it be better to start on the far side of the light strip so that you wouldn’t do this? Comment from : No channel |
|
How is this not shorting out? Comment from : X Y |
|
Really liked your video, I'm going to be trying to solder some led lights soon, so far most videos are full of useless info, yours seems to be to the point, never soldered anything before, I'll update after Thanks again for the video Comment from : Delilah Crigger |
|
How many current/voltage do these leds need? Comment from : blikvisz |
|
How do you connect the bare wires to a war outlet Comment from : Evan |
|
Straight to the point and no extra unneeded vobab Thanks for confirming it is possible to do, brother man Comment from : Kiven Walters |
|
Shakes head Wtf Comment from : Verightess |
|
Can’t see ANYTHING your doing because of the focus!! Comment from : Brian Zakalowski |
|
Microphones help Comment from : overload28 |
|
Sound Echoing from Cave Walls Comment from : goobermint her3tik |
|
cant hear you over the music Comment from : Mike Hunt |
|
I cut the first beginning and i only have 1 side of the connecter Comment from : azryati |
|
Sir can we use only one type of wire Comment from : AARAV VLOGS |
|
The Swan is very unstable, it probably wants to shoot off for a swim, a walk or something I suggest holding the strip down with a paper clamp on the edge of a thin worktop or MDF off cut, you will have better control Good effort though Comment from : kay mbewe |
|
2:40 This is the part I came here for, separating the clear off of brthe copper, an entire video would be in order for this brpart, looks easy, but is far from it, lol Still looking for someone to brbrshow us how to do this part the right way , whatever that might be Comment from : Bikers On Call |
|
Is that security 24/4 wire? Comment from : Alex Babchanik |
|
How do you hook it up to a power source? Comment from : Blake Hollingsworth |
|
Thanks much, I watched your video and did it Success! Thanks much Comment from : Shawn Tittle |
|
Flux is your best friend Grab some RMA and go nutsbrbrAlso the flux included in the core of some solder is not enough The Flux core's only purpose is to get the solder flowing once heat is applied Comment from : Cyrus Epion |
|
dammit im stuck trying to get the silicone off Comment from : Elijah J |
|
love the focus of the camera! Comment from : Mohit Morris |
|
Nope, too out of focus to be even partly useful On to another video Comment from : DonInAlabama |
|
If you don’t have heat shrink can you use electrical tape? Comment from : HardCoreCopper |
|
Tnx I cuted the rgb control box and you got me out tnx Comment from : Majamboi |
|
Focus error Comment from : NS vlogz 373 |
|
What if it touches eachother Comment from : IamHasim |
|
Bruh I don’t even have led lights Comment from : Carlos Andrade |
|
Nice Swan bro Cheers Comment from : Renner |
|
Learn to focus Comment from : Rusty Stork |
|
5:20 "Everyone needs a swan" Nice DIY helping hand brubrVery well done, some flux might help the solder flow better I use a bit of kapton tape to mask off the spot is am soldering which eliminates solder bridges Comment from : Misadventures in Technology |
|
You seem like a cool dude man I gotta explore your channel Comment from : Mark1Mach2 |
|
👓 that's better Comment from : Matthew Reis |
|
youtube/6jr2GQlS6bs Comment from : led biểu diễn |
|
LOL lotta YT'er Martin Scorsese comments if ur concerned about improving ur YT cinematography, OK, otherwise I got the content points u were trying to convey ;-)brbrMartin Scorsese Comment from : E2Thumby |
|
Oh - and here I thought my monitor needed glasses :0) Comment from : Albert Webber |
|
Your a life saver, my soldering is now sticking and not falling off lol, thanks for the video!!! Comment from : Orange Track TV Hot Wheels |
|
Las Comment from : Lakkam swapna |
|
Thanks for the video Just a comment though, the alligator clip mount isn't helping too much because the strip is moving around while soldering, making precise soldering difficult It's better to have weighed down the base of the DIY helping hands with a weight (like a heavy book), or better yet, just taped down the strip to the table The flat shape of the strip makes it very easy to secure with just tape One of the important things I learned during years of soldering is that soldering a moving piece is such a pain and the simple step of making it immovable/fixed helps greatly Comment from : Vendémiaire |
|
Can I use a red black wire for a 4pin ? Comment from : Jebron Lames |
|
DudeI'm learning a lot from this video, so thanks One thing thodon't blow on the solder joint Just like happen to you The wire you had just soldered fell off Cold joints Comment from : Robbie Dukes |
|
Thank you! Comment from : Lilly Williams |
|
What mm heat shrink gets around 10mm led strip with less give? Also get a little better mic? The audio mix is nice in the close up hands shots but the longer shots a bit tough to hear Comment from : Narciso Carlos |
|
Awesome Buddy!! Comment from : SM8 MoTO |
|
Good info, but you gotta review your product prior to publishing your focus made for the loss of what you're showing Comment from : losmon68 |
|
yep I need a smaller tip Comment from : André Mariano |
|
no actually I cant see Comment from : wecnmlwiefmwwwwvfr |
![]() |
How to Solder Led Strip lights #ledstriplights #electronicengineer #electricalengineering РѕС‚ : Hard Wiring Download Full Episodes | The Most Watched videos of all time |
![]() |
How to Solder LED Strip Lights РѕС‚ : Super Bright LEDs Download Full Episodes | The Most Watched videos of all time |
![]() |
How to Solder Wire to Single Color LED Strip Lights - EcolocityLED.com РѕС‚ : Ecolocity LED Download Full Episodes | The Most Watched videos of all time |
![]() |
HOW TO SOLDER LED STRIP LIGHTS РѕС‚ : Crown Molding LED Lighting Download Full Episodes | The Most Watched videos of all time |
![]() |
How to Solder LED Strip Lights РѕС‚ : Environmental Lights Download Full Episodes | The Most Watched videos of all time |
![]() |
How to Solder a Waterproof LED Strip Light РѕС‚ : aspectLED Download Full Episodes | The Most Watched videos of all time |
![]() |
How to Solder a LED Strip Light РѕС‚ : aspectLED Download Full Episodes | The Most Watched videos of all time |
![]() |
How to Solder LED Strips without Soldering Iron DIY / Led Soldering with glue gun РѕС‚ : Haris Ideas Download Full Episodes | The Most Watched videos of all time |
![]() |
water running led strip light, water flowing effect led tape РѕС‚ : Chen Cynthia Download Full Episodes | The Most Watched videos of all time |
![]() |
DIY - How To Solder LED strips - Many Tips And Tricks - Clean And Secure Connections! РѕС‚ : Studjo Infinity Download Full Episodes | The Most Watched videos of all time |