How to Control Stepper Motors with Arduino using a GRBL CNC Shield!

Video quality	The size	Download

Информация о How to Control Stepper Motors with Arduino using a GRBL CNC Shield!

Название	:	How to Control Stepper Motors with Arduino using a GRBL CNC Shield!
Продолжительность	:	8.55
Дата публикации	:
Просмотров	:	15 rb

bang !!! clear crisp on point !!!kudos n thanku :)
Comment from : ganji chetan

cool
Comment from : Adessi pro IGR

Been trying to piece this picture together for a while You gave the whole process in one short video Thanks
Comment from : Tom Carroll

thanks
Comment from : remustrading

Amazing I just, simply followed your vedio step by step, working fine as it is👌👌I am in the process of development of CNC machine As first step to my projectit really worked on one go Thanks a lot 🙏
Comment from : k

Can i follow the same steps if i am using a MKS GEN v14 ? it has a ATMEGA2560 uC, also can i control different motors with the same driver ?
Comment from : Volnei Gabriel Dias Menezes

Is it possible to remove the Stepper motor, and replace it with a linear stepper actuator?
Comment from : Blue Sky

I am new to the board wiring I am going to build CNC machine using UNO and CNC shield I am using Nema 23 Stepper Motor 3Nm(425ozin) 42A & Driver DM542T CNC Kit brHow much power supply is required to run UNO and shield board?brThank you
Comment from : Krunal Patel

Thank you
Comment from : eyyupk

very helpful!
Comment from : Qixuan

Thanks bro✨
Comment from : Ramanan

What was the component you used to bridge the connection on the step increment pins?
Comment from : Walid

I love tinkering around with Arduino but have always found working with steppers confusing, this looks like a really good system and you have explained the set up process in a very easy to understand way, can't wait to give it a try! Great video 👍👍👍
Comment from : 1st Track Dents

I'm all hooked up and connected Flashed the UNO @ 115200 baud, and carefully set it all up in UGSBUT, When I go to move the steppers, nothing happens! I have an "alarm: XYZ Probe" Not sure if that's causing my issue or not I'm stuck here Any help is appreciated Thanks!
Comment from : Steve G

Pretty straightforward, thank you 🙏brbrbrbrbrbr😘
Comment from : Tushe

what feedrate you use to test the motors?in the calibration my motor rotates normaly when i try to jog , it doesnt rotate
Comment from : mpam002

Well done my friend, I was honored and benefited a lot from this beautiful explanation I am a new follower from Egypt
Comment from : alzanaty الزناتى

Thank you for the detailed explanation, saved our project!!
Comment from : Asli Tekeli

Hello sirbrI made cnc machine (Arduino uno grbl ) z and y only one direction run pls help
Comment from : Musaddique Ahmed

I would send gcode from a smartphone to an old CNC Fanuc Sigma VC1000 that has an old rs232 serial 25 pin After that I would monitoring this machine (maybe sending it some command to the serial and the machine could answer me about start, stop, allar, type alarm, but I don't know if it possible, maybe yes) brCould you help me in this little project? Thanks
Comment from : Giova

Hi guys, brI have a bit of a problem I'm hoping someone can help me out with I am not able to connect my UGS with the Arduino and shield it says connecting but doesn't get to connected Has anyone had this issue before? and hopefully got it resolved?
Comment from : Norvin D Costa

I downloaded grbl and had to create the libraries folder for but I can't access it through the examples page Did I miss something?
Comment from : Nikki Lee

when i hit connect it turns orange but at the x, and y controls it keeps on saying connecting
Comment from : Wernich Cronje

Is there a cleaner way to power it looks like you split some wire - would rather buy something that just plugs in is that possible?
Comment from : GuruMack

none of these videos have worked, I am going to make video showing the problem
Comment from : Ronnie Paul

Im having issues with the universal gcode sender (UGS) Cant get it to connect
Comment from : Ola Nordmann

Hello sirbrCan i powar 12v dc 10Amp current
Comment from : Musaddique Ahmed

Clear, simple and straight to the goal
Comment from : Stefano Furlan

i have a problem it goes orange but i cant control anything
Comment from : mr cardboard

Hi Thanks god I stumbled upon your channel Im in the process of learning how to build a cnc machine, and your channel will be very useful
Comment from : Ola Nordmann

For the first time; a video that explains this process perfectly! Thank you!!!
Comment from : Davio Curo

i am building a CNC and was seaching for electronic assemblybrthe quality of this video is so good that i subbed it halfway through brkeep up this good work! thank you
Comment from : VIJAY